鮮切加工設備的使用周期到達一定時間范圍內，是需要進行大幅度的維護保養的，當然為了不那么麻煩，我們?cè)谄匠＞涂梢酝ㄟ^(guò)定期的維護來讓該設備不受損，下面小編就維護保養以及注意事項來講講內容吧。
When the service life of the fresh cutting processing equipment reaches a certain range of time, it needs a large amount of maintenance. Of course, in order to avoid such trouble, we can usually protect the equipment from damage through regular maintenance. Now let's talk about the maintenance and precautions.
維護保養
Maintenance
1、對于鏈條的調整：該調整是在馬達停止之后進行的，在兩鏈輪的中間以手指來壓鏈條，壓縮量一般為4到9毫米之間是標準值，當一旦超過標準值得時候就調整惰輪規定緊度。
1. Adjustment of the chain: the adjustment is carried out after the motor stops. Press the chain between the two sprockets with a finger. The compression amount is generally 4 to 9 mm, which is the standard value. Once the standard value is exceeded, adjust the idler gear to the specified tightness.
2、對于無段變速的更換：無段變速齒輪箱機油之點檢加油及更換，是要停止馬達，嚴禁煙火得情況下拆掉檢油塞，油剛流出為適當之量，不足時補充之。
2. For the replacement of the stepless speed change: For the spot check and oil filling and replacement of the stepless speed change gear box oil, the first step is to stop the motor. It is strictly prohibited to remove the oil inspection plug under the condition of fireworks. The amount of oil just flowing out is appropriate, and it should be supplemented when it is insufficient.
3、長期不使用時的保存：當我們要進行長時間的保存而不使用時我們就可以把各部分的泥土等的物體進行沖洗擦拭干凈，各個回轉部以及皮帶和鏈條等的附著的雜物都要完全的而且各回轉部及磨擦主動部，充分注油以防止生銹現象的出現。
3. Storage when not in use for a long time: When we want to keep it for a long time without using it, we can wash and wipe the dirt and other objects in all parts. The sundries attached to all rotating parts, belts and chains should be completely removed. All rotating parts and friction driving parts should be fully oiled to prevent rust.
注意事項
matters needing attention
一、操作人員使用前應檢查管路系統有無漏氣漏水的情況，如果有應及時解決，并建立設備操作維護日志。
1、 Operators shall check whether there is air or water leakage in the pipeline system before use. If there is, it shall be solved in time, and equipment operation and maintenance logs shall be established.
二、設備運行前應試運行，讓設備先空運轉2-3分鐘，檢查傳動系統和運輸帶的運動是否平穩。
2、 Test run the equipment before operation, let the equipment run for 2-3 minutes without load, and check whether the movement of the transmission system and the conveyor belt is stable.
三、開啟浮油排除裝置，因此時水泵尚開啟，水面平靜，排油效果好，待浮油基本排除后停止除油，排油污多利用休息時間進行。
3、 Start the oil slick removal device, so the water pump is still on, the water surface is calm, and the oil drainage effect is good. Stop the oil removal after the oil slick is basically removed, and the oil stain is mostly discharged during the rest time.
四、將待處理的蔬菜等物料要整齊地放在運輸帶上，不能壓在滾輪上，操作時一定要注意。
4、 The vegetables and other materials to be treated shall be placed on the transport belt orderly, and shall not be pressed on the roller. Pay attention to the operation.
五、操作人員要對我們的蔬菜清洗流水線做好維護。
5、 Operators should maintain our vegetable cleaning line.
鮮切加工設備的維護保養及其他注意事項就講解到這里了，您對此有什么問題要了解或者有什么需求可以隨時來我們網站
http://www.whrjcs.com咨詢！
The maintenance and other precautions of the fresh cutting processing equipment are explained here. If you have any questions or needs, you can come to our website at any time http://www.whrjcs.com consulting service
